The W300CSS 316 Stainless Steel I-LAG™ screw (eye lag screw) is designed to fasten ceiling wire or jack chain to wood surfaces to facilitate the installation of drop ceilings in corrosive or marine environments. The W300CSS is an excellent choice for MRI room applications due to it’s austenitic, non-magnetic properties. Chlorinated environments have been observed… Continue reading 3″ I-LAG™ Eye Lag Screw – 316 Stainless Steel – 100 Pack
Products Category: Suspended Ceiling
T Bar Tools & Fasteners
Doc’s Industries manufactures tools and fasteners to make T Bar suspended ceiling installation faster and easier. We supply just about everything you need to aid in the installation of Donn, Certainteed and Armstrong ceiling tile and grid. Doc’s is home to well known brands such as Lagmaster lag poles and ICC listed I-Lag screws. Be sure to check out our new purpose-built AR-125 rivet tool, designed specifically for suspended ceiling installers.
2 1/4″ Deep Drilling I-LAG™ Eye Lag Screw – Thousand Pack
The New ELDXM – Deep Drilling Eye Lag Screw is designed to go into structural steel up to 1/4″ thick, NOT FOR USE IN SHEET METAL THINNER THAN 12 GAUGE (0.1094″). The ELDXM has a blue Ruspert® finish with an extra wide drill tip. It can drill into 1/8″ steel in less than 5 seconds,… Continue reading 2 1/4″ Deep Drilling I-LAG™ Eye Lag Screw – Thousand Pack
1-5/8″ I-LAG™ Eye Lag Screw – 316 Stainless Steel – Hundred Pack
The W1625CSS 316 Stainless Steel I-LAG™ screw (eye lag screw) is designed to fasten ceiling wire or braided aircraft cable to wood surfaces. Suitable for installation in corrosive or marine environments. The W1625CSS is an excellent choice for installing bird repellent wire or netting. Chlorinated environments have been observed to cause stress corrosion cracks in… Continue reading 1-5/8″ I-LAG™ Eye Lag Screw – 316 Stainless Steel – Hundred Pack
1-5/8″ I-LAG™ Eye Lag Screw – 316 Stainless Steel – Five Hundred Pack
The W1625DSS 316 Stainless Steel I-LAG™ screw (eye lag screw) is designed to fasten ceiling wire or braided aircraft cable to wood surfaces. Suitable for installation in corrosive or marine environments. The W1625DSS is an excellent choice for installing bird repellent wire or netting. Chlorinated environments have been observed to cause stress corrosion cracks… Continue reading 1-5/8″ I-LAG™ Eye Lag Screw – 316 Stainless Steel – Five Hundred Pack
I-DRILL DRIVER SM
Use the I-Drill Driver SM to install specialty I-Lag® screws, Part #’s: W1625CSS & W1625DSS into wood surfaces with a power drill. Designed for use with chuck style drills, not impact drill or drivers.
Overhead Drill Machine
The patented Overhead Drill Machine – Generation 2 is the ultimate all-in-one extension tool for overhead drilling applications. The universal saddle fits most “D” handle, “L” shaped, Pistol grip and Cordless rotary hammer drills. The ODM G2 is the most efficient and effective tool of its kind. Use it to install wedge anchors, tie wire… Continue reading Overhead Drill Machine
I-Pin – Tie Wire Anchor
The I-Pin is a 1/4″ concrete expansion wedge anchor designed for use in suspended ceiling tension applications. It is an excellent choice when powder actuated pins are not practical. Such as fastening into very hard concrete with hard aggregate or in hospitals. A pre-drilled 1/4″ x 1 1/4″ hole is required for installation. Compare to:… Continue reading I-Pin – Tie Wire Anchor
I-Wedge Tool
Use the SDS PLUS I-Wedge Installation Tool to install I-Pins, Eye-Wedge Anchors and Powers’ Tie-Wire Spike Anchors using the “hammer only” feature of an SDS Plus hammer drill. Attaches to any SDS Plus Hammer Drill Weighs .40 lbs.
TorqueExtender
The TorqueExtender™ is a socket wrench extension pole. It allows you to torque down multiple sized fasteners to ceilings safely and easily from the ground. Installs 3/8″ wedge anchors, concrete screws and drop-in anchors with ease. Use what the inspectors use! Standard 1/2” male square socket drive with detent ball Standard 1/2” female square socket… Continue reading TorqueExtender
I-Drill Driver
Use the I-Drill Driver to install I-Lag® screws into metal or wood surfaces with a power drill. Designed for use with Jacobs chuck style drills, not impact drills or drivers.